Curtis 1314 Pc Programming Station Software Download
1314-4402 PC Programming Station. Choose the most popular programs from Design & Photo software Download. Free curtis pc programming station; Top. Users interested in Free curtis pc programming station generally download. Curtis Model 1314 PC Programming Station provide.microprocessor-based. Programming Curtis controller, software?
Hello; I have been reading the forum up and down looking for any clue about my connection problem. As I didn't find anything I am opening this thread (well, I found lots of hints about connection problems and tried many of them, but it seems my problem is somewhat different).
I got a Curtis 1236, used. I don't know much about it's previous settings or use conditions. I tried connecting to it without motor, throttle.Terminal software (putty & dacio) showed error codes (scode x) signaling the parts that were missing, like the motor. Curtis software 1314, however, refused connection: 'Error 0023 Initialization of communication interface failed. Communication error with controller' After assembling all the parts requested by the controller, the controller stopped printing error codes and printed run info like RPM, Amps, etc.I can change that info with the 'menu mode' switch. Again, I can see all that using putty, dacio, etc.
The controller seems to work, it will accelerate the motor (the encoder settings are probably wrong, but it works anyway). But the programmer software still refuses to connect. I have tried 4 differente USB/Serial adapters, some will show the terminal output correctly, others will not. I even tried with an old win98 PC, but the programming software still refuses to connect (terminal work though). Using an oscilloscope I have checked some bits are sent in the TX wire, but still conection is not established.
I did also read about entering commands in the terminal, using ':'. But it does not seem to work; sometimes the output of 'RPM x' info will stop for a moment but will resume activity soon. Some questions for the experts: - I have a 840 display installed, it shares the bus with the programmer cable. Is that ok with the programming process, or should I remove it? Buku panduan bermain gitar fingerstyle pdf.
(I tried with & without). Can be the Curtis controller set up as non-programmable? Is it possible or controller is programmed (using VCL) to avoid programming? - I have seen captures of users sending commands in the terminal. My terminals are full of controller output text (RPM - RPM - RPM.). Maybe there is a 'program mode' or something similar I have overlooked? Hope somebody can offer a clue.
Hello; I have been reading the forum up and down looking for any clue about my connection problem. As I didn't find anything I am opening this thread (well, I found lots of hints about connection problems and tried many of them, but it seems my problem is somewhat different).
Curtis 1314 Programmer
I got a Curtis 1236, used. I don't know much about it's previous settings or use conditions. I tried connecting to it without motor, throttle.Terminal software (putty & dacio) showed error codes (scode x) signaling the parts that were missing, like the motor.
Curtis 1314 Software
Curtis software 1314, however, refused connection: 'Error 0023 Initialization of communication interface failed. Communication error with controller' After assembling all the parts requested by the controller, the controller stopped printing error codes and printed run info like RPM, Amps, etc.I can change that info with the 'menu mode' switch. Again, I can see all that using putty, dacio, etc. The controller seems to work, it will accelerate the motor (the encoder settings are probably wrong, but it works anyway). But the programmer software still refuses to connect. I have tried 4 differente USB/Serial adapters, some will show the terminal output correctly, others will not. I even tried with an old win98 PC, but the programming software still refuses to connect (terminal work though).
Using an oscilloscope I have checked some bits are sent in the TX wire, but still conection is not established. I did also read about entering commands in the terminal, using ':'. But it does not seem to work; sometimes the output of 'RPM x' info will stop for a moment but will resume activity soon.
Some questions for the experts: - I have a 840 display installed, it shares the bus with the programmer cable. Is that ok with the programming process, or should I remove it? (I tried with & without).
I know for a fact you can have a 840, I have one running with a 840 and a 1314 programmer as well as a 1311 - Can be the Curtis controller set up as non-programmable? Is it possible or controller is programmed (using VCL) to avoid programming?
Yes, in VCL you can actually assign access levels. I have seen captures of users sending commands in the terminal. My terminals are full of controller output text (RPM - RPM - RPM.). Maybe there is a 'program mode' or something similar I have overlooked? Hope somebody can offer a clue.
Thanks for replying, I am using 1314-4401 'downloadable version'. I think I remember v3.12 build 35 patch 6. That is same version I use successfully. However, it took me awhile to resolve the connection/communication error. The blue CH340 USB/serial cable is the easiest way to go, but it took me trying different CH340 cables until I found one that worked.
Actually had to have a verified working cable shipped to me from London by WoodyGB. I sent him my non-working cable which he disassembled and found a bad solder joint. It may be as simple as buying a few cheap blue CH340 cables off ebay to get one that will work. They sell for about $3 US.